Discontinued Products

Discontinued product notices

SGE Discontinued Product List 2015 [PDF] 


Replacement parts for discontinued products

Heated syringe cleaners

The heated syringe cleaner is no longer manufactured. Replacement septa for use with it are available.

Part number

Description

041842

7 mm EC Grade Septa, PK50

High efficiency column couplers

The high efficiency column couplers are no longer manufactured. The following spare parts are available.

  • Inert - biocompatible
  • Provide a rigid low dead volume, metal free connection between two components of an HPLC system Ideal for connecting two columns, a column to a guard cartridge or in-line filter
  • Maximum pressure rating: 5,000 psi
  • Thread type: 10-32

Part number

Description

0624351

Replacement PEEKsil tubing (1/16" x 175 µm ID x 50 mm), PK5

0730014

Replacement PEEK ferrules, PK10

MS/FID Splitter Kit

The MS/FID Splitter Kit and Fixed Outlet Splitter are no longer available. The following spare parts are available. Not suitable for use with 0.1 mm ID columns.

 Part number

Description 

073220

Replacement SilTite metal ferrules - 0.4 mm ID, PK10

073221

Replacement SilTite metal ferrules - 0.5 mm ID, PK10

073222

Replacement SilTite metal ferrules - 0.8 mm ID, PK10

073224

Replacement SilTite nuts, PK5

123711

Replacement restrictors - Set A for use with 0.25 mm ID columns, Split ratio 1:1

123712

Replacement restrictors - Set B for use with 0.32 mm and 0.53 mm ID columns, Split ratio 1:1

18614600

Replacement tubing for Fixed Outlet Splitter, Split ratio 1:1, PK2

18614610

Replacement tubing for Fixed Outlet Splitter, Split ratio 1:5, PK2

18614620

Replacement tubing for Fixed Outlet Splitter, Split ratio 1:10, PK2

072662

Replacement 2 hole ferrules for Fixed Outlet Splitter, 0.1-0.25 mm ID columns, PK 10

072664

Replacement 2 hole ferrules for Fixed Outlet Splitter, 0.32 mm ID columns, PK 10

Air Sharp™

The AirSharp™ is a peak-focussing GC accessory that uses ambient temperature compressed air as a coolant to cool a very small area of the capillary column rather than the standard liquid carbon dioxide (CO2) or liquid nitrogen (N2) that are used in many of the currently available cold traps.

Designed to focus individual high boiling, late eluting peaks just prior to the compounds entering the detector, the AirSharp increases the signal-to-noise ratio and sensitivity of individual peaks thereby lowering detection limits and making low-level analyses easier.

The risk of contamination onto the capillary column resulting from excess large volume injections, is also decreased.

This product was discontinued from December 31, 2011. Technical support and replacement parts will be available until December 31, 2017.

Part number Description
72606 Replacement 1/16" (1.2 mm Hole ID) Graphite Ferrule
72657 Replacement 1/16" (1/16" Hole ID) Graphite / Vespel® Straight Ferrule
93391 Replacement 1/16" Connection Tube
103405 Replacement 1/16" Extended Stainless Steel Nut with 1.2 mm Hole
103408 Replacement 1/16" Extended Stainless Steel Nut
113417 1/16" SS tube with restricted end (red marker)
113421 1/16" SS tube with 1/8" sleeve
Cryogenic Trap

Useful for:

  • On-column trace enrichment
  • Air and gas sampling
  • Purge and trap
  • Multidimensional techniques
  • Headspace analysis
  • Splitless injection

Cold Traps use liquid carbon dioxide injected directly into a special Tee fitting surrounding the column. They are suitable for holding components with boiling points equivalent to C7 for 10 to 20 minutes at oven temperatures up to approximately 300°C.

The kit consists of Cold Trap, with pneumatic head switching valve, and all required accessories for installation.

Part number Description
933424 Replacement 50 micron filter for CO2 Inlet
93346 Liquid CO2 Cryogenic Cold Trap - Direct
gc-BackFlush System

  • Reduce analysis time
  • Increase column life
  • Less maintenance required on the GC
  • Reduce column bleed deposits on detectors (eg. FID and MS)
  • Removes semi-volatile and non-volatile material from the front end of the capillary column

This product was discontinued from December 31, 2011. Technical support and replacement parts will be available until December 31, 2017.

Part number Description
93354 Spare BackFlush Tee
93355 gc-BackFlush Restrictor Kit 1
93356 gc-BackFlush Restrictor Kit 2
93357 gc-BackFlush Restrictor Kit 3
ms NoVent II

5 minute GCMS column changeover 

  • Simple operation
  • Easy installation
  • Faster troubleshooting
  • Direct GC-MS Interface
  • Save 6-12 hours column changeover time

The ms NoVent II is designed to allow column, liner or septum changeover, or column maintenance to be carried out, without the need to shut down the MS.

The ms NoVent II is a fluidic valve. The unique design ensures a helium purge maintains a positive flow from the valve to the atmosphere, when a column is not connected. The valve prevents air entering the MS.

The retrofitted ms NoVent II requires:

  • A Control Unit (same for all GC’s)
  • The correct tee for your GC
  • The correct restrictor for your GC (note that for some systems, an adaptor is also supplied with the restrictors)

All three items must be ordered to have a complete ms NoVent II system.

This product was discontinued from December 31, 2011. Technical support and replacement parts will be available until December 31, 2017.

ms-NoVent II Tee and Restrictor/Adaptors - MS Make and Model Specific

Select the correct tee and restrictor for your GC. Please note that for some systems, an adaptor is also supplied with the restrictor.

Part number Manufacturer Model Description
113451 Agilent Technologies (HP) HP5970 Restrictor (Pack of 2)
113452 Agilent Technologies (HP) HP5971/5972 Restrictor (Pack of 2)
113453 Agilent Technologies (HP) HP5973/5975 Restrictor (Pack of 2)
113454 Agilent Technologies (HP) HP5989 Restrictor (Pack of 2)
113455 Shimadzu 2010 Restrictor (Pack of 2)
113455 Agilent Technologies (HP) HP-GCD Restrictor (Pack of 2)
113456 Agilent Technologies (HP) HP5988-A Restrictor (Pack of 2)
113460 PerkinElmer Turbomass/Gold Restrictor (Pack of 2)
113465 Shimadzu MS 5000/5050 Restrictor (Pack of 2)
113466 Shimadzu MS 5000/5050 with wide bore interface Restrictor (Pack of 2)
113470 Thermo Electron GCQ Restrictor (Pack of 2)
113471 Thermo Electron SSQ7000 Restrictor (Pack of 2)
113472 Thermo Electron Voyager Restrictor (Pack of 2)
113475 Thermo Electron Trace DSQ Restrictor (Pack of 2)
113475 Thermo Electron Polaris Q Restrictor (Pack of 2)
113475 Thermo Electron Focus DSQ Restrictor (Pack of 2)
113480 Varian Saturn 2000, 2100, 2200 Adapter and Restrictor (Pack of 2)
113481 Varian Saturn 1, 2, 3 and 4 Adapter and Restrictor (Pack of 2)
113482 Varian Saturn 2000, 2100, 2200 Restrictor (Pack of 2)
113483 Varian Saturn 1, 2, 3 and 4 Restrictor (Pack of 2)
113490 Thermo Electron Focus DSQ Tee
113490 Shimadzu 2010 Tee
113490 Thermo Electron Voyager Tee
113490 Thermo Electron GCQ Tee
113490 Varian Saturn 2000, 2100, 2200 Tee
113490 Thermo Electron SSQ7000 Tee
113490 Agilent Technologies (HP) HP5971/5972 Tee
113490 Thermo Electron Polaris Q Tee
113490 Shimadzu MS 5000/5050 with wide bore interface Tee
113490 Agilent Technologies (HP) HP-GCD Tee
113490 Agilent Technologies (HP) HP5988-A Tee
113490 Agilent Technologies (HP) HP5970 Tee
113490 Agilent Technologies (HP) HP5989 Tee
113490 Varian Saturn 1, 2, 3 and 4 Tee
113490 Thermo Electron Trace DSQ Tee
113490 Agilent Technologies (HP) HP5973/5975 Tee
113491 Shimadzu MS 5000/5050 Tee
113492 PerkinElmer Turbomass/Gold Tee

The instrument restrictors listed below are available as replacement parts for the ms-NoVent system (see images below). This system has been replaced by the ms NoVent II.

ms-NoVent Restrictor/Adaptors - MS Make and Model Specific

Contact us regarding compatibility between original ms NoVent and ms NoVent II parts.

Part number Manufacturer   Model   Description  
113409 Agilent Technologies (HP) 5973 Restrictor (Pack of 2)
113416 Varian Saturn1, 2 & 3 Restrictor (Pack of 2)
ms-OpenSplit

ms-OpenSplit is no longer available, however replacement restrictors are still available.

ms-OpenSplit Restrictor/Adaptors - MS Make and Model Specific

An instrument specific restrictor must be ordered and installed into the MS interface for correct operation of the ms-OpenSplit. For MS instruments other than HP and Shimadzu, an adaptor for the ms-OpenSplit is also required.

Part number Manufacturer   Model   Description  
113409 Agilent Technologies (HP) 5973 Restrictor (Pack of 2)
113416 Varian Saturn1, 2 & 3 Restrictor (Pack of 2)
MDS 6890™

This product was discontinued from December 31, 2011. Technical support and replacement parts will be available until December 31, 2017.

Olfactory Detector Outlet (ODO II)

  • Identify components by odor or fragrance
  • Ideal for cosmetics, flavors and fragrance industries

The Olfactory Detector Outlet is designed to take the outlet stream from a gas chromatograph and transfer it to a nose cone in which it is mixed with a humidified air stream, allowing the operator to use their nose to identify individual components as they elute from the column. The capillary column flow is simultaneously split to an MS detector (or other detector) for the identification of unkown compounds.

The Olfactory Detector Outlet System contains a glass nose cone, detector transfer tube, humidifier, gas control module, splitter kit and all accessories required for installation.

This product was discontinued from December 31, 2011. Technical support and replacement parts will be available until December 31, 2017.

Part number Description
93513 ODO II Glass Nose Cone
93514 ODO II Transfer Line Tubing (320 µm ID)
93515 ODO II MS Restrictor (150 µm ID)
93516 ODO II Column Flow Splitter
93517 ODO II Standard MS Restrictor (125 µm ID)
93518 ODO II Low Vacuum MS Restrictor (110 µm ID)
103489 ODO II Adsorption Tube
113417 1/16" SS tube with restricted end (red marker)
113421 1/16" SS tube with 1/8" sleeve
Pyrojector II™

Pyrolysis chromatography is a powerful analytical tool able to thermally crack (fragment) essentially non-volatile molecules into volatile fragments, making them suitable for chromatographic analysis.  It enables a reproducible and characteristc 'fingerprint' to be generated of a non-volatile sample.  The technique can be applied to such varied tasks as the identification of bacteria, paints, rubbers, polymers, and fibres.

The microfurnace is designed to operate at temperature up to 900°C for extended periods, without Curie Point gaps.

Pyrojector II is an economical, continuous mode microfurnace pyrolyzing injection system which is highly reproducible. It is ideally suited for use with High Resolution Capillary GC, with a range of sample introduction systems designed for both liquid and solid samples.

The Pyrojector II is designed to operate on an existing GC injection port. It can easily be removed or attached, as the need arises for pyrolysis analysis. Sample introduction results in immediate pyrolysis and transfer of the breakdown products to the head of the column.

Applications

  • Polymers
  • Plastics
  • Forensic
  • Bacterial analysis
  • Geochemistry
  • Paint/coatings

Please order your Pyrojector II System via your closest distributor or office.  Please specify the make and model of your GC instrument when ordering to ensure that the correct adaptor is supplied.

The Pyrojector II System includes a furnace, adaptor, control module, solid sampling kit, and installation kit.

This product was discontinued from December 31, 2011. Technical support and replacement parts will be available until December 31, 2017.

Part number Description
9980 SI-7 Solids Syringe
9984 SI-PYRO-11 Solids Syringe
9988 P3 Pellitiser Injector
41845 10mm EC Septa (packet of 50)
726212 1/4" Graphite Ferrules with 6 mm ID (packet of 10)
9321640 Needle Seal from Septumless Injection Head (pack of 5)
950013 Replacement Adapter Agilent Technologies 6890
950021 Replacement Adapter PerkinElmer AutoSystem™ and Clarus®
950043 Replacement Adapter Varian 1075/1077 injectors
950046 Replacement Adapter Varian 1177 injector
950071 Replacement Adapter Shimadzu 17A
950085 Replacement Adapter Shimadzu 14A
950090 Replacement Adapter Thermo Finnigan Trace™
950095 Spare Quartz Sample Tubes (pack of 50)
950120 Spare Quartz Furnace Liners (pack of 2)
950202 Replacement Septum Cap
950203 Replacement Solids Injection Head
950204 Pyrojector Solid Sampling Kit
950205 Replacement Transfer Tube 0.12 mm
950206 Replacement Transfer Tube 0.5 mm
950207 Replacement Furnace Thermocouple
950220 Replacement Furnace
950301 Replacement Control Module
950302 Pyrojector Punch Probe
950303 Pyrojector Quartz Tube Adaptor
18060001 Spare Quartz Wool (0.5g)
Unitrex™

This product was discontinued from December 31, 2011. Technical support and replacement parts will be available until December 31, 2017.

From 31 March 2016, part number 0932922, UTX-IWG Insulation Wedges Pk10, is no longer available.

Part number Description
93292 UTX-B Silanized Glass Beads
932923 Unitrex Carrier Gas Tubes (pack of 10)
932924 Silicone Rubber Tubing with SS Insert (pack of 10)
932925 UTX-CA Cleaning Adaptor
932927 Silicone rubber tubing for carrier tubes (pack of 10)
93293 UTX-SU Unitrex Inlet Head
93294 UTX-C Column Tube & Beads For Unitrex
932940 UTX-CC Empty Column Tube
93295 UTX-R Reservoir
93296 UTX-T Trap
932985 Unitrex-II Thermocouple
93299 UTX-H2 220/240V Cartridge Heater

Instruction manuals

Instruction manuals for obsolete products such as Pyrojector II™ (part number 095000), Olfactory Detector Outlet (ODO II)™ (part number 093510), MS NoVent II™ (part number 113440), gc-Backflush (093352), Air Sharp™ (093390), MDS 6890™ (0933490 and 0933491), Unitrex (part numbers 0932900 and 0932902).

Column Flow Splitter (MS to FID)

High Energy Dynode Detector for Ion Traps and Quadrupoles

Active Film Multiplier for the PerkinElmer QMass Mass Spectrometer

Guard Cartridge Installation Procedure

μ-Flowmeter™ Instructions

ProteCol Flow Splitter Instruction Manual

Installation and Operation of 14121D2 and 14121HD2 Active Film Multipliers

Installing and Operating the 14130 and 14130D2 Active Film Multipliers

Installing the 14570 Detector in an Elan 5000 (serial #<147)

DM133B Detector for RGA Applications with Incorporated Faraday Cup Support

DM274 Miniature Ion Counting Multiplier for Detector Array Applications

Models 14520 and 14521 for General Quadrupole Analogue applications

Active Film Multiplier for the Finnigan ITD Ion Trap GC-MS

ODO-II Olfactory Detector Installation & Operating Instructions

Installation and Operation of 14122 and 14122H Active Film Multipliers

Active Film Multiplier for the Agilent Technologies (HP) 598x series MS Positive Ions Only

Active Film Multiplier for the Agilent Technologies (HP) 598x series MS Positive and Negative Ions Only

Active Film Multiplier for the Agilent Technologies (HP) 5989 MS Engine) Mass Spectrometer

Installing the 14561 Active Film Multipliers (Sciex/PE-Sciex ELAN 500)

Heated Syringe Cleaner Instructions

Column Flow Splitter (MS to FID) - Instruction Manual

Multidimensional Capillary GC System for Agilent Technologies 6890 GC - Installation and Operation Manual

AirSharp Installation Manual

AirSharp Operating Manual

gc-BackFlush System - Instruction Manual

ms NoVent II - Installation and Operating Instructions

ms NoVent I - Installation and Operating Instructions

Pyrojector II - Installation and Operating Manual

MSVT4 Micro Needle On/Off Valves 

MDS2000 Multidimensional Capillary GC System Installation and Operating Instructions

OSS-1 Outlet Splitter System

CHIS Absorption Tubes Packing Instructions

Liquid Nitrogen Cold Trap System CTS-LN (Part Number 093345) Instructions

Capillary Conversion System CCS-4/NC & CCS-05/NC

The Open-Split Capillary Interface (Part Number 113532)

Concentrator/Headspace Injector (CHIS) Installation and operation Instructions (as a kit or when used with control module)

CHIS Tube Conditioning Accessory Instructions

Older style HPLC columns - prior to July 2009

Adaptor Kit for connecting fused silica capillaries to SGE micro needle valves with 1/16" ports

SealTight™ Valves

Solid Sampling Kit for the SGE Pyrojector II

OSS-2 Outlet Splitter System

VSOS Capillary Outlet Splitter

Inlet Splitter (VSIS-2/-3/-5)

Old Style Gas Purifier Instructions

MOV-1 and MOVT-1 On/off Valves & MCV-1 and MCVT-1 Metering Control Valves

How to use Retention Gap Kits RGK-1, and RGK-2

How to assemble your Capillary Washing Reservoir